NEW DURO DYNE FPP5 SERIES AUTOMATIC BULK FEED 5FT. CONVERSION PLATFORM
The FPP-5 is a 110 volt insulation fastening machine designed for use in the HVAC industry. A welding power source is not included with the FPP-5. The FPP-5 is fully assembled for pneumatic and electronic control including;
1.Weld pin feeder and bowl for weld pins up to 2 inches long.
2.Weld pin feed track.
3.Weld pin feed track sensor.
4.Electronic component chassis assembly.
5.Main power, Vibrator power and Dwell cycle control box assembly.
6. Upper weld tip assembly.
7. Lower weld tip assembly.
8. Foot pedal weld activation.
9. Air regulator assembly.
10. Compact 5 foot throat welded frame.
The FPP-5 is to be used in conjunction with the Duro Dyne portable MF12A (DD p/n 27110) Portable hand held welding gun pin spotter as a welding power source (208-230 volt 60HZ) single phase 60 amp service.
The FPP-5 can be purchased with the MF12A or without for Duro Dyne customers who may have previously purchased a Duro Dyne portable MF12A pin spotter.
The FPP-5 receives a welding power source from the MF12A after the MF12A is placed on to the FPP-5 mounting frame weldment and the MF12A ( after removing the hand gun and ground clamp cam locks) is con- nected to a 208-230 volt 60HZ, single phase 60 amp service. The MF12A welding source will transfer power to the FPP-5 by means of connecting the FPP-5 Front and Rear Weld Cable Cam locks and the 24 volt Power/Switch cable to the MF12A.
The FPP-5 is a 110 volt insulation fastening machine designed for use in the HVAC industry. A welding power source is not included with the FPP-5. The FPP-5 is fully assembled for pneumatic and electronic control including;
1.Weld pin feeder and bowl for weld pins up to 2 inches long.
2.Weld pin feed track.
3.Weld pin feed track sensor.
4.Electronic component chassis assembly.
5.Main power, Vibrator power and Dwell cycle control box assembly.
6. Upper weld tip assembly.
7. Lower weld tip assembly.
8. Foot pedal weld activation.
9. Air regulator assembly.
10. Compact 5 foot throat welded frame.
The FPP-5 is to be used in conjunction with the Duro Dyne portable MF12A (DD p/n 27110) Portable hand held welding gun pin spotter as a welding power source (208-230 volt 60HZ) single phase 60 amp service.
The FPP-5 can be purchased with the MF12A or without for Duro Dyne customers who may have previously purchased a Duro Dyne portable MF12A pin spotter.
The FPP-5 receives a welding power source from the MF12A after the MF12A is placed on to the FPP-5 mounting frame weldment and the MF12A ( after removing the hand gun and ground clamp cam locks) is con- nected to a 208-230 volt 60HZ, single phase 60 amp service. The MF12A welding source will transfer power to the FPP-5 by means of connecting the FPP-5 Front and Rear Weld Cable Cam locks and the 24 volt Power/Switch cable to the MF12A.
The FPP-5 is a 110 volt insulation fastening machine designed for use in the HVAC industry. A welding power source is not included with the FPP-5. The FPP-5 is fully assembled for pneumatic and electronic control including;
1.Weld pin feeder and bowl for weld pins up to 2 inches long.
2.Weld pin feed track.
3.Weld pin feed track sensor.
4.Electronic component chassis assembly.
5.Main power, Vibrator power and Dwell cycle control box assembly.
6. Upper weld tip assembly.
7. Lower weld tip assembly.
8. Foot pedal weld activation.
9. Air regulator assembly.
10. Compact 5 foot throat welded frame.
The FPP-5 is to be used in conjunction with the Duro Dyne portable MF12A (DD p/n 27110) Portable hand held welding gun pin spotter as a welding power source (208-230 volt 60HZ) single phase 60 amp service.
The FPP-5 can be purchased with the MF12A or without for Duro Dyne customers who may have previously purchased a Duro Dyne portable MF12A pin spotter.
The FPP-5 receives a welding power source from the MF12A after the MF12A is placed on to the FPP-5 mounting frame weldment and the MF12A ( after removing the hand gun and ground clamp cam locks) is con- nected to a 208-230 volt 60HZ, single phase 60 amp service. The MF12A welding source will transfer power to the FPP-5 by means of connecting the FPP-5 Front and Rear Weld Cable Cam locks and the 24 volt Power/Switch cable to the MF12A.