USED ROOF PANEL MACHINES - ROLLFORMING - ROLLFORMERS -

LINK TO NEW TECH AND ZIMMERMAN -ESE- KNUDSON-JOBSITE-ENGLERT-ROLLFORMER CORP

 
Okay, here's this FLC rib AG Panel machine.

Mill is a all USA built. 17 pass
Runs 40 7/8" Strip in Galvalume or Painted Steel. 26ga. - 30ga., 
29 H.P. Vari-Speed Drive,  Elec: 220/440 3ph.
 
FLC 4ft x 20ga. Pre-Cut Flying Shear, PLC Controller for Length & Count.
Elec: 220v 3ph


 

 
Price for all Components  Loaded Truck Florida ....... $35,000

MIC 240 automatic building machine rollformer and curving machine $45,000

STILL FOR SALE IN HOUSTON TX AREA
 

ULTRA-LOK 2" Armco Standing Seam Panel Machine.

ULTRA -LOCK REDUCED DOWN BIG TIME ONLY $32,500 NOW 

2 SETS OF TOOLING SIMIALR TO THE KNUDSON ROOF PANEL

also has 1 1/2" MECHANICAL STANDING SEAM

 Runs 24 ga - 26ga. Steel. 16" Panel - 28" WIDTH Panels

MACHINE HAS A Striations ASSEMBLY

Gas Engine Hydraulic Drive & Shear WITH AMS MP400 Controller.

One 3,000lb. Coil Reel. Knudson Dual Axle Trailer. Power Seamer.

The Rolls where Replaced New in 2003. Been in Storage Since. 

 Price ....  $32,500.00

 To add to the specs's. The 2" Armco will run up to 22ga. Steel. & .040 aluminum

 Machine has Clip Relief at the S/Seam.  Can run In or Out. Speeds up To 70 FPM,

CUSTOM ROLLFORM  in- plant 1" SNAP LOCK WITH NAIL FLANGE PROFILE. HEAVY DUTY MACHINE

ROOF PANEL ROLLFORMER MACHINE

The machine makes two fixed widths ONLY HAS

12" and 16" wide PANEL CAPABILITY and has a mid mounted shear.

RUNS GREAT AND CAN BE SEEN UNDER POWER NOW.

PRICE HAS BEEN REDUCED ALMOST $8,000

 NEW SPECIAL PRICE $27,995.00 MAKE US AN OFFER PLEASE.

230 volt three phase electric      

elec/hydraulic shear

batch controller

stand alone non powered decoiler

stiffening beads

SORRY SOLD NOW

ON HOLD FOR NOW DOING A JOB

2001 Knudson vp-21 ROOF PANEL ROLLFORMER (1"snap lock tooling), with nail flange  on this factory trailer with gas engine and decoiler, COMPUTER BATCH CONTROL AND STANDS ALSO HAVE OLDER Knudson KR-24 ROLLFORMER,  we need to liquidate call us for additional information.

ASKING PRICE IS $22,500 ON THE VP-21

 SORRY SOLD NOW

, here's an Griffin AG Panel Rollforming machine.

  Model is GSS AG Machine,  14 passes, 3" Shafts, 44" R.S.

Material: 24ga - 29 ga Grade 80, Strip width 40 7/8" 

Mechanical Drive with Hydraulic Shear, NOTE NO BLADES

BLADES ARE $1800 BUT DOES HAVE THE Hydraulic Pack

Control box BATCH Program length of cut.

11,000lb x 48" Manual Reel.  Elec: 220v 1ph 60cy.

 

Price for all Components  Loaded Truck Florida ....... $27,500

GUTTER AAPRON ROLLFORMER

MACHINE FOR SALE NOW

BUILT ON STAND SHOWN

ALMOST NEW RUNS GREAT

WILL SEL AT GREAT PRICE OF $13,000

SHIPS FROM GA.

SOLD

ON OUR WAREHOUSE FLOOR NOW IN ENNIS TX
NOTE BIG SALE 1993 RUNS GREAT IN GOOD COND.

SSP ROLLFORMER NEW TECH MACHINE

1993 SSP Multi Panel roofing machine.

SN: 5351293
1-3/4" SNAP Lock Tooling SS675 series installed .
Box Trailer Mounted Machine Shown ALL TOOLINGHAS BEEN CLEANED AND GEARS REPLACED and some bearings and bushings as needed.
WITH DUAL OVERHEAD RACK AND SPINDLES
5 Run Out Tables

GAS ENGINE WITH BATCH CONTROL IN BOX

Reduced to $24,000 or best offer for the machine

AGAIN ITS IS ON HOLD FOR NOW.

 


 

SORRY SOLD NOW

IKE NEW 2003 ESE 150 Roofpanel rollformer machine
ROOF PANEL ROLLFORMER
SN: T1500903    Yr new 2003

ELECTRIC MOTOR 230 1 PHASE
ESE 150  1-1/2" MECH SEAM TOOLING

SOLD WITH 1 OR 2 DECOILERS AND 1  A FRAME RACK          SALE PRICED at $35,500

CHX AG PANEL ROLLFORMER

NEW in USA Stock. CHX 16 Pass 5 rib AG Panel, 3" Shafts, 48" R.S.,

Mech. Drive with Hydraulic Up Cut Shear. 

Tooled to Run 29ga - 24ga Galv. & Painted Gr. 80- Steel.

PLC Control for Length & Count. Speed: 30 FPM.

Progressive Center Out Alloy Tooling.

New 11,000 x 48" Free standing decoiler reel is included.

22ft L x 5ft wide x 5ft high  wt is 9700lbs ship dim.

Elec: 220v 3ph 60cy.

 Special Price ..........   $33,300 Dealer Loaded Truck Vancouver, Wa., USA

IF NEEDED HERE IS Used Woehr 10,000 lb. x 4ft. Powered Uncoiler. 

Rear Operated Manual I.D: 17" - 21" . Elec: 220v 3ph 60cy  

Price ..... ONLY $7,500

ZIMMERMAN Z PANEL ROLLFORMER ROOF PANEL

BACK ON SALE NOW IN GREAT CONDITION $29,995

SN: 2010 WITH TRAILER AND MACHINE COVER
1- SNAP LOCK TOOLING  SL1000
WITH SPINDLE AND A FRAME RACK WTH STANDS
(5 Run Out Tables)

ALSO STRIATION ASSSEMBLY

GAS ENGINE WITH LIMIT SWITCH CONTROL CTL

SPECIAL ASKING PRICE REDUCED NOW!!   $29,995

STILL ON HOLD Nice Used  NTM  SSH Roof Panel Roolformer with 1" Nailstrip Tooling.

Includes Bead Stiffening rib's.

Optional Tooling Available NTM 1 1/2" and under Profiles

Has AMS Controller, 2 x 3,000 lbs. Overhead Rack and 2 Reels, 30 ft Run-Out.

Gas Powered Hydraulic Drive & Shear. Dual Axle Trailer.

 Price .........   $37,900.00   SELLER BE KEEPING FOR SHORT PERIOD OF TIME.

 


   LIKE NEW  VERY CLEAN Schlebach Quadro. 2004

Has 5 profiles, 1" & 1 1/2" Mech. S/S, 1" & 1 1/2" Snap Clip & 1" Nailstrip

Has Striations, ASSEMBLY AND NEW 3,000lb coil reel, 

Operator Controls &  PLC Controller for Length & Count

Runs on 220v 1ph 60cy  ** Always used in a shop ** Never outside 

 CAN BE SOLD $1,800 LESS WITOUT DECOILER REEL

Price ........  ONLY $33,900.00 Loaded Truck

SORRY SELLER SOLD IT

2007 schlebach quadro panel machine ROLLFORMER  MACHINE HAS the following tooling: 1.5”snap lock, 1.5” nail strip,  and 1.5” mechanical seam  3 SET CASSET ONLY

TRALER AS SHOWN  GOOD CONDITION LIKE PHOTOS SHOWN VIDEO, SOON ALSO HAS SWENSON SNAP TABLE STYLE PANEL BRAKE WITH SAW

ASKING $39K RANGE.

SPECIAL QUICK SALE NOW NICE CONDITION  SCHLEBACH QUADRO SHIPS FROM THE NORTHERN USA

2016 Englert Metal Man Multi Panel roofing machine.

FOR SALE HERE IN DFW TX AREA NOW ! ENGLERT MMP

2 STES OF TOOLING INCLUDED IN PACKAGE DEAL

NOTE BIG SALE 2016 LIKE NEW IN MINT COND. $55K

VERY SIMILAR TO NTM SSQ MACHINE

GAS ENGINE MOTOR WITH TRAILER
1.5" Mechanical Lock Tooling A1300 series installed in mach now also know as 1-1/2 mech standing seam

ALSO 2" MECH SEAM COMMERCIAL TOOLING

NTM Trailer we be sold with instead of special trailer shown.
DUAL Overhead Rack
1 SPINDLE & ARBOR included
1 Batch Computer control
Reduced to $55,000 or best offer for the machine

2 SETS OF TOOLING NOT JUST ONE.

SOLD WITH NTM TRAILER NOT SHOWN IN PHOTO

 

 

SORRY SOLD NOW ON HIS WAREHOUSE FLOOR NOW UP NORTH US
ON SALE 2017 RUNS GREAT NEW MINT CONDITION

ZIMMERMAN COMMERCIAL  ROLLFOR


GAS ENGINE WITH BATCH CONTROL IN BOX AND MOUNT. 8 BOXES OF CLIPS FRO THE 1-1/2 SNAP LOCK

HE ORIGINALLY PAID 82K FOR IT. VIDEO BELOW

SCHLEBACH QUADRO PLUS ROLLFORMER LIKE NEW 2000

WAKE UP ! ON SALE NOW MINT CONDITION

2000 schlebach quadro PLUS panel machine ROLLFORMER  MACHINE HAS the following tooling: 1-1/2" snap lock tooling

1-1/2" Mech Standing Seam

1-1/2" with nail flange  3 profiles on  3 cassettes TOTAL

DOES NOT HAVE  RIB OR striations BUT YOU CAN ORDER

GOOD CONDITION LIKE PHOTOS SHOWN CNC BATCH CONTROL AND VIDEO, SOON . sold with cart on wheels

NO TRAILER PRICE IS REDUCED TO $44,000 RANGE.

ON SPECIAL QUICK SALE NOW, NICE CONDITION  SCHLEBACH QUADRO PLUS IN GA.. SEE YOU TUBE VIDEO LISTED AT BOTTOM OF THIS PAGE BEFORE SOLD ITEMS.

-

LIKE NEW NEW TECH  2012 NTM SSR JR 2 SETS OF tooling
ROOF PANEL ROLLFORMER WITH 2 SETS TOOLING NOW
SN: 2091112 ELECTRIC MOTOR 230 1 PHASE
FF100 snap with nail flange  WITH TRAILER AND RUNOUT

SS150 1.500 " MECH SEAM TOOLING
LIMIT SWITCH CUT MANUAL LEVER G. SHEAR.
SOLD WITH 2 DECOILERS MOUNTED
SALE PRICED at $35,000 IN TX LOCATION NOW

CAN BE SOLD WITHOUT TRAILER AND GENERATOR $32,000

SORRY SOLD NOW

NEW TECH SSQ LIKE NEW 2016 DELIVERED IN SEP 2016

2016 NEW TECH SSQ panel machine ROLLFORMER  MACHINE HAS FWQ-100  1" FLAT WALL SOFFIT PANEL TOOLING SET

SSQ-550 1-1/2" SANP WITH CLIP WITH 5 X 10FT RUNOUT STANDS

 

ON SPECIAL QUICK SALE NOW, SEE YOU TUBE VIDEO BELOW

SOON

ENGLERT METAL MAN 650 COMBO GUTTER MAKER 5-6"

ENGLERT METAL MAN MACHINERY 2017 MODEL 

FOR SALE NOW AT GREAT PRICE. REDUCED NOW $8,500
BIG SALE NOW ON SEAMLESS GUTTER MACHINE

WITH 2 DECOILERS AND ELECTRIC ENGINE

PRICE IS REDUCED NOW FOR QUICK SALE

LOCATION NY GREAT PACKAGE DEAL AVAILABLE NOW

ONE CUSTOMER ONLY HAS OWNED THIS MACHINE

THIS IS AS NEW AS IT GETS, MINT CONDITION.

LIKE THE NEW TECH MACHINE

 

 


ROLLFORMER FOR TRIM WORK J Channel Line

  J" channel roll form line

runs a 1" high leg "J" channel, 5" strip for part, 24ga - 20ga.

Contour 12 pass gearhed mill, 2" shafts, 9" R.S.

15 HP DC motor with electric drive and operator controls

Tishken 18 ton hi speed mechanical press with flying shear

ASL 2500 lb. powered uncoiler, manual I.D.: 16" - 21"

Elec: 220/440v 3ph 60cy

 

Price ....... $34,000.00 loaded truck

ZIMMERMAN COMMERCIAL  ROLLFORMER ROOF PANEL

SN: 20

ON HIS WAREHOUSE FLOOR NOW UP NORTH US
ON SALE 2004 RUNS GREAT NEW MINT CONDITION

-

1-SNAP Lock Tooling series installed .
1-1/2" ITERGRAL SNAP LOCK TOOLING  SS550
WITH SPINDLE AND A RACK INCLUDED WTH STANDS
(5 Run Out Tables) ALSO STRIATION ASSSEMBLY

GAS ENGINE WITH BATCH CONTROL IN BOX AND MOUNT

SPECIAL NOW ASKING $39,995

 Englert 1500/16 Snap Lock S/S machine.

-

-

It runs a 16" wide x 1 1/2" snap lock w/clip panel. Two removable stiffening ribs.

Gas powered hydraulic drive and shear. Lever controls, one for run and one

for shear. (no length control ) 3000lb coil reel with stand. Skid base.

 -

Price ..........  $22,500.00  

LIKE NEW 2012 GRIFFIN AG PANEL STEEL ROLLFORMER

Auto Cut to length system with 3 programmable lengths. forward reverse. It has a variable speed from I think 20 to 70 fpm. Cuts clean.

11 Pass 5 rib AG Panel, 3" Shafts, 48" R.S.,

Rollers for each RIB AND every shaft. 1 phase 220 VOLT  single phase. PRICE REDUCED -$3,000 TO $26,000

Mech. Drive with Hydraulic Cut Shear. 

Tooled to Run 29ga - 24ga Galv. & Painted Gr. 80- Steel.

PLC Control for Length & Count. Speed: 20-70 FPM.

New 10,000 x 40" Free standing decoiler reel is included.

22ft L x 5ft wide x 5ft high  wt is 9700lbs ship dim.

Elec: 220v 1 ph 60cy.

 Special Price .......... NOW ONLY  $26,000 Dealer Loaded  USA

EASTSIDE ABC seamless equipment.
This is an Eastside built seamless siding machine with five profiles!

Comes with all guillotine shears, overhead hoist and box truck.

The facia gutter machine uses 13 1/4 inch gutter coil.

$35,000
1/2 of new

SORRY SOLD

KNUDSON KR-24 1993 MODEL
Get set up for Residential & Commercial

Knudson KR 24 Structural Panel Forming Machine.
2 SETS OF TOOLING (1.5" and 2" MS - MECHANICAL STANDING
Gas Engine Hydraulic Drive & Shear WITH AMS MP400 Controller.
One 3,000lb. Coil Reel, Run out tables, Knudson Dual Axle Trailer. Compressor, Generator and Hot Melt Capability.

SPECIAL NEW TECH SSP MINT CONDITION WITH TRAILER

2005 Runs SSP200 : 2" and SS150 : 1 1/2" Mech. S/Seam profiles.

HAS Striations ASSEMBLY INCLUDED ALL BELOW FEATURES

Gas powered hydraulic drive and shear.

AMS Controller. LOW HRS ON THIS MACHINE 2 sets of profiles

2 - 3000lb reels

20ft run-out. Factory trailer.

2 - powered seamers. FOR EACH PROFILE

 ASKING PRICE IS $49,000 FOB GA.

SPECIAL NEW TECH SSQ MINT CONDITION WITH TRAILER

2012 Runs SSQ  WITH SS100R : 1" Mech. S/Seam profile TOOLING  $48,500 WHAT A DEAL!!! THIS IS A SSQ

HAS Striations ASSEMBLY INCLUDED ALL BELOW FEATURES

GAS POWER WITH HYD SHEAR CUT OFF

AMS COMPUTER Controller. LOW HRS ON THIS MACHINE

DUAL OVERHEAD RACK WITH 2 - 3000lb DECOILER reels

50ft run-out. 5 STANDS TOTAL AND  Factory MAXEY trailer.

 REDUCED PRICE AGAIN LOWERED !!!

 ASKING PRICE IS $48,500 FOB HOUSTON TX

ENGLERT METAL MAN MULTI PANEL MACHINE

ON SALE NOW ON OUR TX FLOOR 2014 GOOD COND.ITION

VERY SIMILAR TO NTM SSQ MACHINE  MECH 1" TOOLING

2014 Englert Metal Man Multi Panel roofing machine.
A1301 : 1 " Mechanical Standing Seam tooling installed in mach OPTION TOOLING 1-1/2" MECH SEAM OR 1-1/2 "SNAP LOCK COST EXTRA $7,000 EITHER SET NOT BOTH

COMPUTER batch control 5 hp Gas Engine MOTOR

MAKE US AN offer for the machine TODAY HERE ON OUR FLOOR IN ENNIS TX CALL US NOW

 


 

1" MECH STANDING SEAM ROOF PANEL MACHINE $24K

KNUDSON MACHINE BUY IT NOW CALL US FAST!

MACHINE IS 2008 Knudson VP-21 panel forming PROFILE IS 1.0" Mechanical Seam OR STANDING SEAM
Includes: Panel Machine, Chassis, Hydraulic cutoff - 110 single phase electric motor, 3000 lb Coil Reel, NATM - compliant 12K Trailer,

Striation Rollers AMS computer CONTROL AND  run-out stands   $24,000 MAKE OFFER

5RN- AG PANEL ROLLFORMER LIKE NEW APRIL 2018 in USA 

CHX 16 Pass 5 rib AG Panel, 3" Shafts, 48" R.S.,

Mech. Drive with Hydraulic Up Cut Shear. 

Tooled to Run 29ga - 24ga Galv. & Painted Gr. 80- Steel.

PLC Control for Length & Count. Speed: 30 FPM.

Progressive Center Out Alloy Tooling.

New 10,000 x 48" Free standing decoiler reel is included.

22ft L x 5ft wide x 5ft high  wt is 9700lbs ship dim.

Elec: 220v 3ph 60cy.

 Special Price ..........   $32,500 Dealer Loaded SEE YOU TUBE VIDEO

RFC ROLLFORMER CORP VS-150 ROOF PANEL MACHINE

READY SOON WITH 1"-1-1/2 MECH STANDING SEAM

PROFILE TOOLING ON PA

FLOOR AT SALE PRICE $38,000 INCLUDES REEL DECOILER

 VS-150                                                                     $29,700

Digital Controller                                                        $ 4,200

FLAT RIB ROLLER ASEMBLY ATTACHMENT               $1,800

ONE 3000 LBS DECOILER W STAND                        $1,500

FREIGHT CHARGE TO YOUR LOCATION special     $1,000

REG PRICE TOTAL                                                $38,200

1”-1½” Snap Lock Dies    option only not included.      $ 1,500

 

Knudson 1.5" Mechanical Seam Electric Seamer. Seller works for a Roofing company in Colorado he aquired machine from a co-worker who no longer is in the roofing business. cleaned it up and took it apart to make sure nothing was broken on the inside. Everything is in great condition besides the trigger to the Milwaukee Drill is broken. It still works but can be repaired for $50. Machine has single stage seaming rollers. The machine has been tested and works as it should.  Year - Unknown ; Make ESE Model - 1.5" Single Stage Mechanical Seamer ; Hours of Use - Unknown;. See All the Photos below shown here.  Asking Price only $1,995

SORRY SOLD ↑      1999 Knudson KR-24 Portable
MODEL KR-24 SN: T-11188
Roll Former – 2” Mechanical
 Standing Seam Roof Panel
Description: Roll Forming machine

to produce 2” mechanically seamed

standing seam panel (width from 12” – 24”).
1-1/2 Mechanical seam can be purchased for only $6,000 from Knudson


Condition: Good
Location: Houston, TX
d.      Asking: $25,000

SORRY SOLD
ENGLERT MOBIL ROLLFORMER SERIES 1000

1993 Englert ROOF Panel 1000 roofing machine.
1.5" SNAP Lock Tooling 1000 series installed in mach now. SOP 1.5 MECH SEAM DOUBLE LOCK

is avail from RFC for $1500 only AMSI Clips

THIS IS RFC JOINT VENTURE MFG. MACHINE
Englert Trailer Mounted Machine With Electric

Motor WITH BUILT IN ONBOARD GENERATOR
ALSO STIFFENING /PENCIL RIB ROLLERS

1 DUAL Overhead Rack
2 FIXED SPINDLES

BACK ON SALE

SALE AT 23,500 or best offer for the machine.

 

SORRY SOLD NOW

NOTE BIG CHANGE IN TOOLING LISTED CORRECT NOW!

2008 Englert Multi Panel roofing machine.
1.5" Mechanical Lock Tooling 1300 series installed in mach now
1-3/4 Snap Lock Tooling 2000 series can be sold separate
Englert Trailer Mounted Machine
Overhead Rack
2 Expandable Arbors
5 Run Out Tables
1 Batch Computer
Reduced to $51,000 or best offer for the machine

$48,000 without 1-3/4 snap lock tooling. A 2000

 

SOLD SORRY

ON SALE NOW 1 ROOF PANEL ZIMMERMAN Z PAN
WITH DECOILER AND STAND machine RUNs FINE.   HAS 1-1/2" SL1000 SNAP LOCK TOOLING.

OTHER SET OF TOOLING IS 1" SNAP LOCK

BLACK MACHINE SKID FRAME BOLT ON ANY TRAILER.

HAS A STRIATION ASSSEMBLY AND RIB ALSO ELECTRIC ENGINE WITH REMOTE AND CORDS.

IT DOES NEED THE LIMIT SWITCH MEASURE DEVICE

NOTE WHITE TRAILER IS SOLD AND GONE NOW.

WE ARE ASKING  ONLY $21K  MAKE US OFFER

SEE VIDEO RUN BELOW

SORRY SOLD NOW

ON HOLD MAY BE SOLD WAIT ON VIDEO INSPECT.

 

Metal Master AG Machine New in 2014. was originally in FL

Has 14 passes, 2 1/2" shafts. Runs 26ga. - 29 ga. Gr 80 Steel

Base Machine. Has Target control. has machine operator control AIR Shear has BUTTON control to activate. Elec: 220v 1ph.

Decoiler Reel. entry roller and exit tables Loaded on truck

 Machine was HARDLY USED. All in good condition

SORRY SOLD

ON SALE NOW RFC this Roll Former Corp. 5 V machine

 Machine doesn't NOT LOOK GREAT but WE know it runs. OWNER will make sure all is cleaned and lubricated before shipping. IT HAS 5000 lb x 30" reel, The factory PLC control.

Elec: 115v/220v 1ph 60c

 

Price ......  $16,500.00 Loaded Truck

NEW TECH GUTTER MAKER 5-6 COMBO

SALE PRICE REDUCED $11,5005

NEW TECH MACHINERY

 FOR SALE NOW AT GREAT PRICE. $11,500 RANGE

LOCATION TEXAS GREAT PACKAGE DEAL AVAILABLE

SEE SSQ TOOLING LISTED BELOW ALSO.

 


 BRAND NEW NEW TECH 2 NEW 2017 NTM SSR JR $29,500

SPECIAL QUICK NEW MACHINE SALE IN STOCK NOW
SN: 2018 ELECTRIC MOTOR 230 1 PHASE 2 SETS TOOLING
SS1500 is 1-1/2 mech standing seam tooling- or SS450 1-1/2 SNAP LOCK WITH CLIPS
FF100 1" SNAP LOCK WITH NAIL STRIP ALSO AVAIL.ABLE
LIMIT SWITCH CUT MANUAL LEVER G. SHEAR.
SOLD WITH 2 DECOILERS AND 1 OVERHEAD DUAL RACK

TRAILER IS NOT INCLUDED. $29,500 FOB PA

1 SS675  FOR SSP MACHINE
View Profile

FF100
View Profile NEW TECH SSP USED TOOLING SET FOR SALE .

 SSP TOOLING FOR SALE NOW SS675 = 1-3/4 SNAPLOCK  $9,995

 SHIPS FROM SOUTH CAROLINA

Metal Master AG Machine New in 2001

ON SALE NOW SEE LIVE ON VIDEO $11,500 SPECIAL

was originally in FL

Has 14 passes, 2 1/2" shafts. Runs 26ga. - 29 ga. Gr 80 Steel

Base Machine. Has Target control. has machine operator control HAND Shear  Elec: 220v 1ph.

Decoiler Reel. entry roller and exit table Loaded on truck

 All in good condition

ALL ITEMS FORM HERE DOWN ARE MACHINES THAT HAVE ALREADY BEEN SOLD

SPECIAL NEW TECH SSQ MINT CONDITION WITH TRAILER

2017 Runs SSQ  SELLING WITH 1 SET OF SS 150  : 1"1/2 Mech. S/Seam profile  OR SL450 1-1/2" snap lock with clip

OR THE FF100 1" SNAPLOCK WITH NAIL FLANGE.

3 SETS TOTAL TO CHOOSE FROM YOUR CHOICE   MACHINE HAS RIB ROLLERS AND STRIATION

YOU CAN CHOOSE TO BUY 2 SETS OF YOUR CHOICE.

GAS POWER WITH HYD SHEAR CUT OFF SN: 7100917

AMS COMPUTER Controller. LOW HRS ON THIS MACHINE

DUAL OVERHEAD RACK WITH 2 - 3000lb DECOILER reels

40ft run-out. 4 STANDS TOTAL AND  Factory MAXEY trailer.

 ASKING PRICE IS $59,900  OR 2 SETS AT $67,000

KNUDSON KR-24 REDUCED DOWN BIG TIME ONLY $19,500 NOW 

KNUDSON ROOF PANEL

Standing Seam Panel Machine.

a1 1/2" MECHANICAL STANDING SEAM

 Runs 24 ga - 26ga. Steel. 16" Panel - 28" WIDTH Panels

Gas Engine Hydraulic Drive & Shear TARGET Control STOP

One 3,000lb. Coil Reel. Knudson Dual Axle Trailer. Power Seamer.


 

2016 Englert Metal Man Multi Panel roofing machine.

NOTE BIG SALE 2016 LIKE NEW IN MINT COND. $49,000

VERY SIMILAR TO NTM SSQ MACHINE 2 SETS OF TOOLING

A1300 : 1-1/2" Mechanical Standing Seam tooling installed in mach Additional  A1000 : 1-1/2" snap lock tooling & comes with COMPUTER batch control 5 hp Gas Engine seen behind control SPINDLE & ARBOR ON STAND included 5 Run Out PRICE Reduced to $49,000 WITH BOTH SETS OF TOOLS

ENGLERT 1100A ROOF PANEL ROLLFORMER

WAKE UP ! ON SALE NOW GOOD CONDITION

SPECIAL It's a Englert 1100A 16" x 1 1/2" snap clip panel.

Electric motor hydraulic drive and exit shear, Englert PLC controller. 2500lb reel.

RUNS FINE CAN BE SEEN UNDER POWER

ASKING $16,500 FOB GA

 Here's a good MRS double high AG/PBR roll form line.

New 2001  MRS 16 pass double high

Runs AG/Tuff panel and PBR panel, Components.....

10,000lb entry coil car, hydraulic power

10,000lb. powered uncoiler, loop control, power I.D.: 17" - 21", hydraulic powered

4ft powered entry pinch roll, power shear and entry belt conveyor  Entry edge guides

16 pass double high mill, 46" RS x 3"shaft

Operator control station with PLC controller

Elec: 220v 3ph 60cy

 

Price .....   $83,500.00 loaded truck

 USED ASC geared head rafted R / PBR line FOR R PANEL

14 Pass x 3 1/2" shaft x 44" R.S. 

Runs 26g & 24g galvalume and pained steel. 43" strip

ASC hydraulic post cut flying shear 

BECK SII touchscreen controller system. ( new in 2015 @ $27k cost )  Operator control station

35 ft drop leaf stacker

20,000lb x 48" Littell powered uncoiler, loop control, power I.D: 18 1/2" - 22"

Elec: 440v 3ph 60cy

 

Price ....  $79,500.00  loaded truck

SPECIAL NEW TECH SSQ MINT CONDITION WITH TRAILER

2017 Runs SSQ450/450SL  : 1"1/2 SNAP LOCK CLIP PANEL

1-1/2" snap lock PANEL and SSQ 200/210A 2" MECH SEAM

AND 2" ARMCO PANELS ALSO  FF100 1" MECH SEAM

RIGHT HAND SIDE ONLY NEEDED ON THIS

3 SETS TOTAL WITH STRIATION

ROLLER ASSEMBLY AND ALL THE BELOW FEATURES

GAS POWER WITH HYD SHEAR CUT OFF

AMS COMPUTER Controller. LOW HRS ON THIS MACHINE

DUAL OVERHEAD RACK WITH 2 - 3000lb DECOILER reels

30ft run-out. 3 STANDS TOTAL AND  Factory MAXEY trailer.

 ASKING PRICE IS $65,900 FOB SAN ANTONIO TX

NICE USED EASTSIDE Roof Panel Roolformer with 1" Nailstrip Tooling. Includes Bead Stiffening rib's.

Optional Tooling Available

Has LIMIT SWITCH CTL , 2 x 3,000 lbs. ON Rack and 2 Reels, 30 ft Run-Out.

ELECTRIC Powered Hydraulic Drive & Shear. Dual Axle Trailer.

 Price .........   $21,900.00   SELLER READY TO SELL NOW SE VIDEO BELOW